Functional Storage: ящики, Controler and автоматический Warehouse

Conventional boxes are suitable for a large number of repeatable items. Unique equipment with different properties, random books and tools are kept separate. Otherwise, a small stream of different items will take useful storage types designed for mass products.

Make one box, put a low-cost resource in it and check input and extraction. Then select the capacity and number of compartments. A large capacity of one type is not equal to many different slots.

If you use Configuring Tool to block the contents, check it in one box: remove the entire resource and make sure that the assignment is retained. This lockdown is necessary so that an empty box does not take up a random automation item. It is not a right-of-access system for players.

Controller - shared access to linked mailboxes. Placement nearby is not enough: the author describes the binding through Linking Tool.

1. Place the Controller where the common line is connected.
2. Use the Linking Tool on the controller to select it.
3. Bind the required boxes in the valid area.
4. Feed one item through the Controller and check which box it goes into.
5. Test extraction via the same common interface.

You can look at the tool mode and group linkage in your output hint. Do not check the tool for the entire warehouse with the first push: first, make sure which controller is selected and if the addition is being implemented, rather than removing the connection.

For several access points, Control Access Points are available; the old descriptions contain the name Controller Extensions. This is access to the existing system after correct reference, not a separate full set of boxes. Follow the name of the object in your version.

Storage Upgrade does not create automatic transport. If the box has become more expensive but does not take away the crop, check the Pulling or external tube. For improvements, adjust the working party in the specified interface.

First, test the transmission between two normal equipments with one resource. Then connect the machine. Automation of the machine may have a separate entrance, fuel slot and exit, so successful connection to the chest does not yet prove access to the right side of the machine.

Check the limits and filters before removing the overcrowding. The overfilled warehouse stops production markedly, and destruction of a rare object may remain undetected for a long time. Leave a separate route for valuable by-products.

Comacting Drawer shows the interrelated forms of one resource, e.g. a scrap and block, when supported transformation exists for them. These are not separate independent stocks: removal of the block spends the appropriate amount of basic material.

First, use a common known resource and check both sides of the transformation. Do not consider any recipe with nine similar ingredients safe compaction. Modpaks can change recipes and authorized changes.

The Simple Comacting Drawer is designed for two performances, and the normal version is designed for a more complete set of supported forms. Choose the type by your task. If you need an exceptionally large stock of one original item, a simple box can be sufficient.

Armory Cabinet is designed for a large number of non-conforming items. The author describes access through external storage facilities such as AE2 or Refined Storage. Therefore, the lack of a conventional chest interface does not prove the loss of contents. Before mass filling, connect the reading method and check the return of the test item.

Fluid Draver stores fluid and requires compatible liquid connection. The subject tube does not replace it. First, test one liquid and check that the system does not attempt to direct the rest of the factory's products into it.

Ender Dravers can synchronize content by frequency. The author describes copying through Linking Tool: read one box and apply to another. Check the tool hint and result on empty test boxes. The total stock cannot be considered as two independent copies of resources.

Connect external access to Control via the appropriate Storage Bus or External Storage. Then find one test item at the terminal, put an extra one and take it back. Set the priority so that mass resources go into selected boxes rather than out-of-control disks.

If the items are visible in the box but are not present at the terminal, check the attachment, range, rights and filters of the external connection. If the terminal sees them but the order is not complete, the problem may already be relevant. autocraft AE2, and not to the capacity of the boxes.

Retrieved November 1, 2026: Functional Storage page and Buuz135 repository. Confirmed functions are described; numerical capacities and ranges should be checked against the installed output.